[Coco] VCC Experience

[Bill Nobel]

Oh I do have both, just can’t remember which is the better for vt100.

BillNobel

On May 25, 2014, at 7:56 PM, Bill Pierce via Coco <coco at maltedmedia.com> wrote:

> 
> Bill, Supercomm should be on the VHD you have.
> 
> 
> Bill Pierce
> "Today is a good day... I woke up" - Ritchie Havens
> 
> 
> My Music from the Tandy/Radio Shack Color Computer 2 & 3
> https://sites.google.com/site/dabarnstudio/
> Co-Webmaster of The TRS-80 Color Computer Archive
> http://www.colorcomputerarchive.com/
> Co-Contributor, Co-Editor for CocoPedia
> http://www.cocopedia.com/wiki/index.php/Main_Page
> E-Mail: ooogalapasooo at aol.com
> 
> 
> 
> 
> -----Original Message-----
> From: Bill Nobel <b_nobel at hotmail.com>
> To: CoCoList for Color Computer Enthusiasts <coco at maltedmedia.com>
> Sent: Sun, May 25, 2014 9:44 pm
> Subject: Re: [Coco] VCC Experience
> 
> 
> Hmm, I have to break out the Supercomm now (or was it OSterm?) To use Telnet 
> now.
> 
> Bill Nobel
> 
> On May 25, 2014, at 5:43 PM, Aaron Wolfe <aawolfe at gmail.com> wrote:
> 
>> Yep, all of the /n devices have a "virtual modem" behind them that
>> understands all of the standard Hayes AT commands.  This lets you use /n as
>> a direct replacement for standard serial devices in any OS9 telecom
>> programs (terminal emulators, BBSes, UUCP, etc have all been tested with
>> good results).
>> On May 25, 2014 7:40 PM, "Bill Nobel" <b_nobel at hotmail.com> wrote:
>> 
>>> Are you serious?  I never would of thought that, but thinking about it.
>>> DW4 is a serial protocol on a virtual serial port.
>>> 
>>> Bill Nobel
>>> 
>>> On May 25, 2014, at 5:29 PM, Aaron Wolfe <aawolfe at gmail.com> wrote:
>>> 
>>>> On May 23, 2014 10:47 PM, "Bill Nobel" <b_nobel at hotmail.com> wrote:
>>>>> 
>>>>> Well, after a little makefile searching, I found what I needed.  I
>>> played
>>>> with telnet to my raspberry pi,  for a bit, works good except vt100 codes
>>>> are coming through so ‘ls' breaks telnet with error 208.
>>>> 
>>>> Using a terminal emulator works better.
>>>> 
>>>> Supercomm is in the nitros9 project and works well.   Start it with /n as
>>>> an argument, I.e.:  supercomm /n
>>>> 
>>>> Then use the DW Hayes AT commands to connect:  ATD1.2.3.4:5678
>>>> 
>>>> That way you'll get reasonable ansi/vt100 terminal emulation and a
>>> channel
>>>> where control codes won't cause issues.  Any terminal program should
>>> work.
>>>> 
>>>> --
>>>> Coco mailing list
>>>> Coco at maltedmedia.com
>>>> http://five.pairlist.net/mailman/listinfo/coco
>>> 
>>> 
>>> --
>>> Coco mailing list
>>> Coco at maltedmedia.com
>>> http://five.pairlist.net/mailman/listinfo/coco
>>> 
>> 
>> -- 
>> Coco mailing list
>> Coco at maltedmedia.com
>> http://five.pairlist.net/mailman/listinfo/coco
> 
> 
> -- 
> Coco mailing list
> Coco at maltedmedia.com
> http://five.pairlist.net/mailman/listinfo/coco
> 
> 
> 
> -- 
> Coco mailing list
> Coco at maltedmedia.com
> http://five.pairlist.net/mailman/listinfo/coco