[Coco] eBay 6309 chips
computerdoc at sc.rr.com
Sat Apr 19 01:36:37 EDT 2014
I appreciate your advice too. I have actually tried adding more solder when
I was desoldering various parts over the years. Sometimes it works and
other times not so much. I don't do it often enough to stay good at it. I
tried to remove an ATX power supply connector from an old PC motherboard a
while back using a solder sucker which I use to be pretty good at as well,
but I was only able to free about half the pins and after messing with it
for quite a while, I ended up ordering one after a friend helped me find a
part number. Thanks again for your help. Take care my friend.
From: coco-bounces at maltedmedia.com [mailto:coco-bounces at maltedmedia.com] On
Behalf Of John Strong
Sent: Saturday, April 19, 2014 1:00 AM
To: coco at maltedmedia.com
Subject: Re: [Coco] eBay 6309 chips
Indeed 6809 chips are more precious than they used to be, but so is the pc
board you are removing they from.
If want to try to salvage them without investing in the "proper" tools here
is a couple of tricks I have used in the past.
Before unsoldering add a bit of solder (Radio Shack's is OK)to each pin.
Typically your solder will have a lower melting point than the solder used
on the pc board. The new solder will mix with the old lowering its melting
Next use a "pro" quality desoldering wick (not RadioShacks or use a liquid
flux with it) and remove as much solder as possible.
Sometimes this is all that will be need. Use the desoldering iron if
necessary, overheating can damage the chip and/or the pc board. A lifted pc
trace is permanent damage, while a 6809 can still be replaced.
> Message: 8
> Date: Fri, 18 Apr 2014 23:39:58 -0400
> From: "Kip Koon" <computerdoc at sc.rr.com>
> Subject: Re: [Coco] eBay 6309 chips
> To: "'CoCoList for Color Computer Enthusiasts'" <coco at maltedmedia.com>
> Message-ID: <firstname.lastname@example.org>
> Content-Type: text/plain; charset="us-ascii"
> Hi Chester!
> How are you going to remove the old 6809 chips from your Cocos? Are
> you going to desolder them in what I would call a proper manner or are
> you going to destroy them by cutting the pins? I've heard people cut
> their 6809s out to make it easier to desolder the pins left behind
> which I can certainly understand. I just can't see destroying a
> perfectly good 6809 chip since they are becoming quite precious these
> days. I too want to upgrade all my Cocos as well. I just have not been
> able to perfect my desoldering techniques. The tip on my desoldering
> iron from Radio Shack is a bit too big to perform the job properly.
> I want to put all my 6x09 microprocessors in sockets as well. Until
> the new
> 6309 microprocessors are tested, then obviously their condition is
> If the pins on the 6809 are cut and the new 6309 is bad then the Coco
> is down for the count and temporarily out of the picture. That is a
> risk I'm not willing to take. Besides, I just don't like destroying
> fully functional chips - that is unless they are Fritos Scoops! ;D
> Please don't take my thoughts in a bad way. I'm just trying to figure
> out how best to accomplish my upgrades so I guess I'm thinking out
> loud. That's something I do a lot. I seem to think much better if I
> think out loud or write down my thoughts in letters or emails. Anyway,
> the 6809 to 6309 upgrade situation has been on my mind for quite a
> while now. I do hope that your 6309 upgrades on all your Cocos goes
> successfully and without any intermediate problems. Take care my friend.
> -----Original Message-----
> From: coco-bounces at maltedmedia.com
> [mailto:coco-bounces at maltedmedia.com] On Behalf Of Chester Patterson
> Sent: Friday, April 18, 2014 8:56 PM
> To: 'CoCoList for Color Computer Enthusiasts'
> Subject: [Coco] eBay 6309 chips
> Hi. I'm going to pop the 6809s on my Cocos and put in 6309s.
> I am looking to buy some 6309 IC's on eBay. The ones I'm looking at
> are at
> Is there any experience on the list with this seller/these chips?
> Suggestions? Recommendations?
> Thanks much.
> Costa Rica
> Come for the beaches! Stay for the beer!
Coco mailing list
Coco at maltedmedia.com
More information about the Coco