[Coco] Altera

[Zippster]

Hi Michael,

That’s with no analog board attached? Just the DE1?

I know the power supply is a little insufficient when running off of the USB
supply if an analog board is attached, but with the AC supply plugged into
the DE1 I’ve never heard of an issue.

- Ed


> On Oct 20, 2017, at 10:43 AM, Michael Furman <n6il at ocs.net> wrote:
> 
> Ed,
> 
> How hard would it be for you to add a power connector to the analog board re-run? On my DE-1 the power supply is just _barely_ sufficient and sometimes it doesn't turn on the first time.
> 
> --
> Michael R. Furman
> Email: n6il at ocs.net
> Phone: +1 (408) 480-5865
> 
>> On Oct 19, 2017, at 2:02 PM, John B <trymyz at gmail.com> wrote:
>> 
>> That would be great.  I am definitely interested.  Mark me down for one.
>> 
>>> On Thu, Oct 19, 2017 at 4:57 PM, Zippster <zippster278 at gmail.com> wrote:
>>> 
>>> John,
>>> 
>>> I don’t have any right now, but I’m considering another run as there seems
>>> to
>>> be enough interest again.
>>> 
>>> They were $110 including a new plexi top plate and proper standoffs when
>>> I did them last time, mostly due to the very expensive SRAMs used.
>>> 
>>> I’ll have to reprice everything as it’s been quite a while, hopefully I can
>>> knock that cost down a little.
>>> 
>>> I’ll make some posts and see if there’s enough demand to do a run of
>>> boards.
>>> 
>>> - Ed
>>> 
>>> 
>>>> On Oct 16, 2017, at 4:20 PM, John B <trymyz at gmail.com> wrote:
>>>> 
>>>> Ed,
>>>> 
>>>> How much are the analog boards?  Do you currently have any extras?
>>>> 
>>>>> On Mon, Oct 16, 2017 at 3:05 PM, Zippster <zippster278 at gmail.com> wrote:
>>>>> 
>>>>> Just as a side note…
>>>>> 
>>>>> He seems to have quite a few available, and this would be a good
>>>>> opportunity for
>>>>> people to get into the CoCo3FPGA project.
>>>>> 
>>>>> I can do another run of analog boards to go along with the DE1 if
>>> there’s
>>>>> enough interest,
>>>>> and we can get a bunch of new users set up.
>>>>> 
>>>>> - Ed
>>>>> 
>>>>> 
>>>>>> On Oct 16, 2017, at 1:31 PM, Salvador Garcia via Coco <
>>>>> coco at maltedmedia.com> wrote:
>>>>>> 
>>>>>> It is impossible to determine what a fair offer is for the seller. If
>>>>> $75USD is a good deal, I am not sure how much lower he is willing to
>>> go. I
>>>>> have sent him an offer for $65 USD. If he accepts I'll pay that. If not
>>>>> I'll just pay the $75 USD. Salvador
>>>>>> 
>>>>>> 
>>>>>> On Monday, October 16, 2017, 10:14:12 AM CDT, Zippster <
>>>>> zippster278 at gmail.com> wrote:
>>>>>> 
>>>>>> These normally sell new for $150-$160 plus shipping.
>>>>>> 
>>>>>> $10 does indeed sound a bit low…  :)
>>>>>> 
>>>>>> Under $100 is a good deal on a DE1 board.
>>>>>> 
>>>>>> - Ed
>>>>>> 
>>>>>> 
>>>>>>> On Oct 16, 2017, at 10:03 AM, Salvador Garcia via Coco <
>>>>> coco at maltedmedia.com> wrote:
>>>>>>> 
>>>>>>> Offering $10 or $20USD seems low. Dave mentioned offering $10USD less
>>>>> than what the seller was asking for. If he is asking for $75 then an
>>> offer
>>>>> of $65 might be accepted.
>>>>>>> 
>>>>>>> Salvador
>>>>>>> 
>>>>>>> 
>>>>>>> 
>>>>>>>  On Sunday, October 15, 2017, 11:32:04 PM CDT, Carlos Camacho <
>>>>> idevgames at gmail.com> wrote:
>>>>>>> 
>>>>>>> So I made a bid for $10 and it was declined. Then a bid for $20 and it
>>>>> was
>>>>>>> declined. With the high shipping costs it looks less than ideal.
>>>>>>> 
>>>>> 
>>>>> 
>>>>> --
>>>>> Coco mailing list
>>>>> Coco at maltedmedia.com
>>>>> https://pairlist5.pair.net/mailman/listinfo/coco
>>>>> 
>>>> 
>>>> --
>>>> Coco mailing list
>>>> Coco at maltedmedia.com
>>>> https://pairlist5.pair.net/mailman/listinfo/coco
>>> 
>>> 
>>> --
>>> Coco mailing list
>>> Coco at maltedmedia.com
>>> https://pairlist5.pair.net/mailman/listinfo/coco
>>> 
>> 
>> -- 
>> Coco mailing list
>> Coco at maltedmedia.com
>> https://pairlist5.pair.net/mailman/listinfo/coco
> 
> 
> -- 
> Coco mailing list
> Coco at maltedmedia.com
> https://pairlist5.pair.net/mailman/listinfo/coco