[Coco] Cross Post from the Facebook Page about the RGB2VGA Board

John B trymyz at gmail.com
Fri Jul 10 23:11:13 EDT 2015


Ed,

I have some flux and electronics cleaner I use.  Alcohol works good but
takes way to much to clean rosin flux.  Even my flux cleaner takes some
effort.  Its the cheap stuff from the local electronics store.  I should
probably invest in the more expensive flux cleaner.

On Fri, Jul 10, 2015 at 11:05 PM, Zippster <zippster278 at gmail.com> wrote:

> I’m following this thread with interest, as I’m going to be finishing up
> theRGB2VGA boards that people had ordered from Kip
> to get that project successfully completed.
>
> It is true that different monitors are more or less tolerant to certain
> differences in signals, that could explain
> some of what is being seen here.
>
> Regarding cleaning boards, 91% isopropyl alcohol works wonderfully.  What
> I do is submerge the boards in the iso in a small
> tupperware type container, soak for 10 minutes or so, brush them with a
> toothbrush while in the bath, then rinse with fresh iso and air dry.
> Be sure to use the 91%, the lower concentrations have too much water in
> them.  It’s available at drug stores, walmart, etc.
>
> - Ed
>
>
> > On Jul 10, 2015, at 9:39 PM, Steve Batson <steve at batsonphotography.com>
> wrote:
> >
> > John,
> >
> > Have you changed the resistors yet, or are you using the resistors
> recommended for the design? I was seeing jitter, where the entire screen
> would jerk and occasional waves going through it mostly noticeable on the
> edges. Also, it didn't seem consistent, sometimes it was worse than others.
> Based on what Roger had found, it sounded like there were a number of
> issues being caused by the original resistor values. Voltage Levels were
> not what they should be. Also there was issues with the HSYNC and VSYNC
> again caused by original resistor values. Luis and posted on the FB page a
> response to one of my questions that some CoCo's are noisier than others
> and this may very well be true, but I'd guess symptoms could be worse on
> some systems then others which could be the combination of the CoCo and
> Monitor. From discussions with Roger about this and how he fixed it, I'm
> going to go out on a limb here and suggest that with his suggested resistor
> values, the video will most likely be crisp, clean and jitter free on most
> any CoCo and VGA monitor unless they have problems of their own.
> >
> > It was a bit of a pain in the butt pulling a bunch of resistors out and
> replacing them with Rogers suggested values, but I'd highly recommend it if
> you haven't done so already. It was totally worth it! If you have already
> replaced the resistors with the new values and are still having issues, I'd
> suggest the following:
> >
> > 1) Inspect your board and make sure you have no possible shorts. Clean
> it real good with alcohol or other good electronic board cleaner and
> thoroughly dry.
> > 2) Check all the cables including power going to the board and make sure
> all is well
> > 3) Make sure the ribbon cable isn't right next to a transformer
> including the CoCo power power supply (thought I am not having issues even
> if set the board right on top of the CoCo above the transformer). This
> probably is NOT an issue.
> > 4) Remove wire I mentioned that was a ground fix.
> >
> > Anyway, let me know if you have changed the resistors yet or not. I'm
> very curious to see where you are at.
> >
> >
>
>
> --
> Coco mailing list
> Coco at maltedmedia.com
> https://pairlist5.pair.net/mailman/listinfo/coco
>


More information about the Coco mailing list