[Coco] Wcreate in OS-9 L2

Bob Devries devries.bob at gmail.com
Fri Oct 17 22:48:42 EDT 2008


Can you give the actual error number?

There's actually two possible CRC errors; a disk CRC error and a module CRC 
error. I'm not in the same location as my manuals right now (~6000 km nort 
of them....), so I can't tell you the relavant numbers.


----- Original Message ----- 
From: "George Ramsower" <georgeramsower at gmail.com>
To: "CoCoList for Color Computer Enthusiasts" <coco at maltedmedia.com>
Sent: Saturday, October 18, 2008 10:37 AM
Subject: Re: [Coco] Wcreate in OS-9 L2


> From: "Robert Gault"
> Sent: Friday, October 17, 2008 11:44 AM
> Subject: Re: [Coco] Wcreate in OS-9 L2
>
>
>> George Ramsower wrote:
>>> When I run wcreate it accesses the disk for something that sometimes 
>>> returns a CRC error.
>>>
>>> What is wcreate doing with the disk. I figured it might be using grvdrv, 
>>> so I make a new copy of that in the cmds dir.
>>>
>>> Actually, I think it's the disk drive as this only occurs when the 
>>> machine is cold. I'll have to try another drive to find ouy, but I was 
>>> curious as to what wcreate is doing with the disk drive while creating 
>>> the windows.
>>>
>>> George
>>>
>>
>> You should post the exact command sequence you are using.
>>
>> In general, wcreate does not access a disk for anything. However, wcreate 
>> is not normally in memory so if you issue a wcreate command, wcreate must 
>> be loaded from a disk.
>> Try loading wcreate before issuing any wcreate commands and see if you 
>> still get disk activity.
>
> I should have told how I was using it. It's in the startup file as 
> follows:
>
> echo Creating Windows
> wcreate -z
> /w1 -s=2 0 0 80 24 0 2 2
> /w2 -s=2 0 0 80 24 0 2 2
> /w3 -s=2 0 0 80 24 0 2 2
> /w4 -s=2 0 0 80 24 0 2 2
>
> The line to echo always works. I put that in to see if it got that far.
> It echos and then the disk acts like it loads wcreate, then begins 
> seeking... slowly, then exits the startup file with no reports of errors.
> Usually, I just kill the one background task and type /d0/startup and it 
> USUALLY works. When it doesn't, it reports the CRC error after the echo 
> Creating Windows line.
>
> Since the startup file doesn't have a CRC, this means that the wcreate is 
> giving the CRC error. Tonight, when I booted, the same thing happened. So 
> I called the startup file as usual with:
> /d0/startup
> And for the first time, I got an error 216. Did a dir and error 216 
> resulted. However, I ran "cold" and the system did reset to RSBASIC. I 
> figure maybe there's something not right in the structure of the FAT?  A 
> reboot worked this time, but I still had to re-run the startup file
>
> The next step was to do a single disk backup using the same disk for 
> source and destination. I won't know until I reboot tomorrow when the coco 
> is TOTALLY cold if this helped.
>  This annoyance began a few months ago and I expected the problem was the 
> power supply and bad cap/s. When that wire on the Y-cable came loose a few 
> weeks ago and we all brain worked over that one was when I began seriously 
> trying to find a bad cap. BTW, this is my CNC coco machine.
>
>  I still think it's the floppy drive. Won't know until I do the isolation 
> trick or, if the backup cleaned it up.
>
> I'm using the Disto SC II no-halt controller.
>
>
> George
>
> --
> Coco mailing list
> Coco at maltedmedia.com
> http://five.pairlist.net/mailman/listinfo/coco 




More information about the Coco mailing list