[Coco] CoCo shedding some weight (and heat!)

[Salvador Garcia]

 Thanks Robert, I found your video informative. I want to do more research to better understand USB C. 
So, for example, If I want to use the trigger board set at 12V, I would need a PD power supply that at least provides 12V? Is that correct?
I appreciate your help in understanding this. Salvador
    On Tuesday, July 25, 2023 at 08:15:27 PM CDT, Robert Emery via Coco <coco at maltedmedia.com> wrote:  
 
 Sorry, missed the last question...
 In the CoCo there are red, blue and black wires. I was using a socket with
white wires that didn't demonstrate this very well, as I had it handy and
always avoid cutting the original if I can.
 Anyway, the blue and red wires should both go to +12v and black to ground.


On Tue, Jul 25, 2023, 2:55 PM Salvador Garcia via Coco <coco at maltedmedia.com>
wrote:

>  Thanks Bob! I'll get tot hat video soon enough.
> I have question about the Cutting the Cord video.
> The trigger board that you used is fixed at 12V?
> You showed the PD power supply very briefly, what is its output rating? I
> imagine that it is at least 12V, but no idea about the wattage,
> You did not show how you soldered the three white whites to the trigger
> board. How are these connected. You mentioned that the whites go to
> positive and the black one goes to ground, but I did not see a black wire,
> maybe it was hiding behind the white wires?
> Also, you did not show how the male power header was connected to the CoCo
> motherboard. I assume that at least 12V DC is expected at this connector? I
> know that the motherboard has a full wave bridge rectifier to convert AC to
> DC. The DC output goes to the SALT chip. Does that mean that the output of
> the PD trigger board connects to the output of the rectifier?
> Sorry I am taking so long in getting these questions out. Other stuff has
> kept me away and I wanted to rewatch your video a few times to make I
> understood what I needed to ask. Thanks! Salvador
>
>
>
>
>    On Tuesday, July 18, 2023 at 03:48:11 PM CDT, Robert Emery via Coco <
> coco at maltedmedia.com> wrote:
>
>  Yes, that's another of my videos... Feel free to ask questions!
>
> Bob
>
> On Tue, Jul 18, 2023, 12:17 PM Salvador Garcia via Coco <
> coco at maltedmedia.com> wrote:
>
> >  By reading the title I thought it was you who had lost weigh due tot he
> > extreme heat going around..
> > I am interested in power supplies, so I'll be sure to give this video a
> > look. I also watch your other video about the case for the GoTek (at
> least
> > I hope it was your video). I have a GoTek that I've been meaning to
> connect
> > to a CoCo 2/3, but not sure how the jumper on the drive go. I already
> > updated the firmware. Salvador
> >    On Monday, July 17, 2023 at 07:40:16 PM CDT, Robert Emery via Coco <
> > coco at maltedmedia.com> wrote:
> >
> >  Modernize your CoCo 3 power supply...
> > https://youtu.be/tTwTgGR-jSU
> >
> > Cheers!
> >
> >
> >
> > --
> > Coco mailing list
> > Coco at maltedmedia.com
> > https://pairlist5.pair.net/mailman/listinfo/coco
> >
>
> --
> Coco mailing list
> Coco at maltedmedia.com
> https://pairlist5.pair.net/mailman/listinfo/coco
>
>
> --
> Coco mailing list
> Coco at maltedmedia.com
> https://pairlist5.pair.net/mailman/listinfo/coco
>

-- 
Coco mailing list
Coco at maltedmedia.com
https://pairlist5.pair.net/mailman/listinfo/coco