[Coco] UK PAL CoCo1 Repair

[Josh Harper]

hi there 
I have several coco 1 motherboards  they are 25 each  with all chips plus 7.95 shipping
what model number is your coco


      From: R Jones <rjones at biketech.org>
 To: coco at maltedmedia.com 
 Sent: Saturday, September 23, 2017 11:19 AM
 Subject: [Coco] UK PAL CoCo1 Repair
   
Thanks for all the help and suggestions, much appreciated.

It is possible have could have made an error while removing some of the ICs to check and socket them. I will try find time this next week to go over each and double check no tracks have been damaged or any other faulty traces.

I did notice that the 10k pot just under the 2n6594 seemed loose, once I had desoldered it one of the legs fell off, so that may have been one issue. Replacing it has not changed the situation. This is strange because I don't remember adjusting this at all.

As most of the simple logic ICs are still available and cheap, I have ordered replacements for them just in case. Although I am trying not to just replace every component on the board! I could of course just look on eBay for a working CoCo, but I would like to get this one running without replacing the whole mainboard.


Rob


On 21/09/2017 13:58, Zippster wrote:
Sorry meant to send this to the list.....

On 21/09/2017 13:58, Zippster wrote:
  > Well, if power seems goods, and the IC’s seem good, I think I’d take
a close look at
  > the reset circuit if you haven’t already.

Yep one of the problems I had with the CoCo and some Dragon motherboards
during the development of DragonMMC was that the Xilinx CPLD would pull
the reset line low due to the rather weak pullup on it leading to the
machine not coming out of reset and having a screen full of random junk.

Fixed it with a diode and reistor between CPLD and reset line.

Also worth checking that the IRQ, FIRQ, NMI and HALT lines are high, (or
possibly pulsing at 50Hz in the case of IRQ)

  > If that looks good I might start poking around with the scope,
probably starting at
  > the CPU/SAM looking for the expected signals and bus activity and
working out
  > from there.

Yep check for E, Q pulsing, R/W will generally be pulsing though less
regularly, ass should Address and Data lines.

  > It sounds as if the video system is working ok, so you’re probably
good there.
  > It does sound like a CPU/memory problem of some sort.

Agreed if you are getting a picture with junk on the screen then the
6847 and probably the SAM also are working in this board. (I know you
verified them in another machine).

  > You may want to verify the BASIC ROM just to make sure it hasn’t been
corrupted/damaged
  > in some way.  Just to make sure the system isn’t simply crashing on
bad ROM code.

I think he said he tried it in a Dragon and it worked there, which would
seem to mean it's probably working.

Have you tried blindly typing MOTORON and listening for the relay click?
If that works the CPU is working and your fault lies somewhere between
the RAM and the VDG, I believe there is an LS373 latch there.

Something that I have also seen fail is the LS244 buffer between the RAM
data outputs and the CPU data bus, can't remember if you checked those.

May also be worth checking for shorts / continuity on the data and
address lines and between the pins of any chip that you have desoldered
and replaced as it's all too easy to solder splash short between tracks

Note that on the CoCo and Dragon, unlike almost all other micros of the
period, the data in and data out of the RAM chips are not connected
together, so need tracing separately.

Cheers.

Phill.


-- 
Coco mailing list
Coco at maltedmedia.com
https://pairlist5.pair.net/mailman/listinfo/coco